NUMERICAL MODELING OF DETERMINING THE ROCKWELL HARDNESS NUMBER OF A STEEL SAMPLE
DOI:
https://doi.org/10.33042/2522-1809-2024-4-185-25-30Keywords:
structural materials, Rockwell method, finite element model, indenter, hardnessAbstract
In steel Hardness is a mechanical property that indicates the resistance of a material to local plastic deformation caused by mechanical indentation. In engineering, hardness is mainly used to determine the properties of various materials. In mechanical solids, the study of the hardness of materials is usually limited to the study of metals and their mechanical behavior. To understand the mechanism of hardness in metal structures, a basic understanding of materials science is necessary.
Accurate hardness measurement is of great practical importance in the technical diagnosis of potentially hazardous industrial equipment (pipelines, pressure vessels, metal structures). This is primarily due to the fact that this characteristic has a strong correlation with strength and yield strength, which largely determine the possibility of further operation of the equipment. At the same time, one of the main advantages of hardness measurement is the speed of its determination and the non-destructive nature of its control.
A finite element model was developed for the indentation process, and the contact radius and contact pressure were obtained. The Rockwell hardness measurement process was modelled in accordance with the test methodology of DSTU ISO 6508-1:2013. The indentation process was modelled using ANSYS software with different contact models and different loads.
The relevance of solving the problem of modelling the process of determining the surface hardness number using the FEM software ANSYS is determined by the high degree of automation of the solution process. During the modelling, it is assumed that the material of the sample into which the indenter of any shape is pressed is homogeneous isotropic and elastoplastic according to the kinematic plasticity model. This model corresponds to the behavior of steels. In addition, the indenter material is isotropic and linearly elastic. In the developed numerical model, the indenter is taken in the form of a tungsten carbide ball, which corresponds to the scheme for determining the hardness number on the "B" scale.
In conditions of limited access to laboratory equipment, numerical modelling of the process of determining the hardness number allows students to demonstrate all stages of the test at a qualitatively new level, and further, to compare with the results of full-scale tests.
References
Prokopovych I.V. (2020). Metallurgy: a textbook, Odesa: Ecology, 308.
Riumin V.V., Riumina E.A., Aheyenko S.B., Liashenko I.Yu. (2021). Experimental and numerical study of the work of flat steel specimens in tension. Scientific Bulletin of Construction, Vol. 105(3), 99-105. https://svc.kname.edu.ua/index.php/svc/article/view/475/466
L. Ma, S. Low, J. Zhou, J. Song, R deWit (2002). Simulation and prediction of hardness performance of Rockwell diamond indenters using finite-element analysis. Journal of Testing and Evaluation, Vol. 30(4), 265-273.
Datcheva, M., Chalakova, G., Iankov, R., & Stoychev, D. (2017). Numerical simulation of nanoindentation tests - lessons learned. International Conference NDT Days 2017, June 12-16, Sozopol, Bulgaria. e-Journal of Nondestructive Testing, Vol. 22(11). https://www.ndt.net/?id=21711
L.A. Dobrzański, A. Śliwa, T. Tarski (2009). Finite Element Method application for modelling of mechanical properties. Computational materials science and surface engineering, Volumе, 1 issue 1, 25-28.
Antunes, J.M., Menezes, L.F., Fernandes, J.V. (2006). Three-dimensional numerical simulation of Vickers indentation tests. International Journal of Solids and Structures, Vol. 43, 784-806. https://doi.org/10.1016/j.ijsolstr.2005.02.048
Mihaela Simion, Mircea Cristian Dudescu, Radu Chiorean (2018). Numerical simulation of Vickers micro-indentation test to estimate micro-hardness. Acta technica napocensis Series: Applied Mathematics, Mechanics, and Engineering, Vol. 61, Issue IV, November, 593-602.
L. Wang, X.H. Zhong (2014). Finite Element Simulation of Surface Micro-Indentation Behavior of Yttria Stabilized Zirconia Thermal Barrier Coatings with Microstructural Characteristic of Columnar Grains and Sub-Grains Based on A Nonlinear Contact Model. International Journal of Computational Materials Science, 244-256.
S.P.L. Madhumali, J.A.S.C. Jayasinghe, C.S. Bandara and A.J. Dammika (2021). Sensitivity Analysis of Brinell Hardness Number to Material Properties of Structural Steel: A Numerical Study. Engineer: Journal of the institution of engineers, Sri Lanka, Vol. 54, Issue: 4, 75-85. DOI: http://doi.org/10.4038/engineer.v54i4.7472
A. Wagih (2016). Experimental and Finite Element Simulation of Nano-indentation on Metal Matrix Composites: Hardness Prediction. International Journal of Engineering (IJE), TRANSACTIONS A: Basics, Vol. 29, No. 1, (January), 78-86. DOI:10.5829/idosi.ije.2016.29.01a.11
P. Victor, P. Catalin, V. Mihai, V. Ionelia, S. Elena-Manuela, and P. Doru (2014). Finite Element Method for Simulating the Vickers Hardness Test. Applied Mechanics and Materials, Vol. 555, 419-424. DOI:10.4028/www.scientific.net/AMM.555.419
W. Rule. (2008). Finite Element Modeling of Brinell and Rockwell Hardness Testing of Metals. Problems Involving Thermal-Hydraulics, Liquid Sloshing, and Extreme Loads on Structures, 191-196. DOI:10.1115/PVP2004-3048
Downloads
Published
How to Cite
Issue
Section
License
The authors who publish in this collection agree with the following terms:
• The authors reserve the right to authorship of their work and give the magazine the right to first publish this work under the terms of license CC BY-NC-ND 4.0 (with the Designation of Authorship - Non-Commercial - Without Derivatives 4.0 International), which allows others to freely distribute the published work with a mandatory reference to the authors of the original work and the first publication of the work in this magazine.
• Authors have the right to make independent extra-exclusive work agreements in the form in which they were published by this magazine (for example, posting work in an electronic repository of an institution or publishing as part of a monograph), provided that the link to the first publication of the work in this journal is maintained. .
• Journal policy allows and encourages the publication of manuscripts on the Internet (for example, in institutions' repositories or on personal websites), both before the publication of this manuscript and during its editorial work, as it contributes to the emergence of productive scientific discussion and positively affects the efficiency and dynamics of the citation of the published work (see The Effect of Open Access).